Wednesday, October 6, 2010

Bow Tutorial

A few weeks ago I posted a Bow Holder project I had made for all my daughters hair bows. I mentioned then that I would post a Hair Bow Tutorial at some point in the future...
So here it is!

There are a lot of ways to make hairbows - mine probably isn't the best/most professional/easiest way. It's just the way I do it - and it works for me! My daughter is VERY (over)active, and these stay together for her - so I must be doing something right!
Type A: The Boutique Bow

To start I cut two lengths of ribbon based on what size I want my bow to be. I singe the ends with a lighter and fold them into loops. I use hot glue to attach mine - a very tiny bit! Otherwise you won't be able to gather the bow in the center.

(I used to use sewing glue, but found that hot glue holds about a millions times better and dries about a million times quicker)

Put one loop inside the other and turn them so they make an X

Then cut your additional ribbons. For this bow I used 1 wide organza ribbon and 4 coordinating gross grain ribbons (2 of each pattern.)

Again, I singe the edges with a lighter, then layer the ribbons on top of my X.

I use super thin floral wire to wrap the middle as tight as I can get it.


At this point I added another ribbon - it felt like it needed some more pink.

Then I choose a coordinating ribbon to use as the center wrap and attach it with a dot of hot glue.

I attach the barrette to the back of the bow with (yep!) more hot glue - then wrap the ribbon over it.

And there it is!

Type 2: The Pony Bow

I just learned how to make this style, and I love it. I actually purchased one from Gymboree so I could examine it closely. Mine are just as fabulous as theirs are, and are SO MUCH CHEAPER.

Start with several pieces (I used 10) of coordinating ribbon in different widths and patterns cut to about 14 inches long.

Make sure they're nice and flat - I use a 1/2 inch flat iron to smooth mine out.

You're going to choose two "main" ribbons to become your T for the bow. One will be the bottom, the other will be the top. They should match each other.
Start with the bottom ribbon and begin crossing ribbons over the top of it.


The goal is that no two ribbons sit directly on top of each other - so you can see them all when it's laying flat - but you want to keep them pretty close together or the ribbons don't fall as pretty when it's in the pony tail.

Once they're all laid out how you want them, sew them together. You don't have to use a machine for this, but I did.


Sew it in an X, so you're sure to get all the ribbons.

Then you take your elastic, stand it up right and use your second "T" ribbon to attach it.

I marked where I wanted it and sewed the first side without the elastic in it.

Then I slid the elastic back in and sewed the second side down.

And that's it.


Here it is in my daughters pony tail. I love this style of bow! It's so sweet - but a little more "grown-up" looking :)


3 comments:

Kimmie @ Sugar and Dots said...

I have been wasting my time making big boutique style bows- this is going to save me time, MONEY, and hours of stress-induced baking. ;) Thank you for the tutorials- LOVE that pony bow!

Jess and Brandon said...

Thanks for the tutorials Mandy! I have tried several times to make cute bows but I'm just not great at it. I'm gonna try the pony bow, I can probably handle that! Plus it's super cute. Love the colors you used too!

Anonymous said...

I know this is quite awhile since you posted this tutorial but I was hoping you could help. I can't, for the life of me, get the florist wire tight around the ribbon. Is there a trick to getting it tight and not looking super sloppy? Any advice would be greatly apprecitaed! I posted as "anonymous because I don't understand my other choices. :)

Related Posts with Thumbnails